5 in 1 Metal can cooler with bottle opener, Sublimation ready blanks R – ACC Sublimation Blanks & Designs

Product Description

Metal can holder for sublimation. White. Insulating metal can holder. 16oz. Includes built in bottle opener on the bottom. Holds the tall, skinny cans, regular can, and bottles. Can be used as a regular tumbler as well with additional screw on slider lid with attached handle, included. Includes screw on top for holding.
Metal can holder for sublimation. White. Insulating metal can holder. 16oz. Includes built in bottle opener on the bottom. Holds the tall, skinny cans, regular can, and bottles. Can be used as a regular tumbler as well with additional screw on slider lid with attached handle, included. Includes screw on top for holding cans and bottles. (rubber bottom sold separately if desired) Shiny white sublimation coating that produces vibrant colors. For use in a mug press or convection oven. Convection oven requires the use of shrink wrap to apply pressure during baking, sold separately, and accessories such as rubber bottoms are also available in a separate listing. ***Convection Oven Directions*** PLEASE NOTE: equipment varies and so may your required settings. Please test your own equipment using these baseline recommendations. Apply sublimation transfer on the surface of the tumbler using heat tape. For full wrap designs, make sure you pull the transfer as tightly as possible around the tumbler, then tape very well along the seam and around the top/bottom of the tumbler. Pulling the tape/transfer as tight as possible with no air pockets. If your transfer does not fully cover the tumbler surface, apply blowout/butcher paper to the entire tumbler so that there is no metal showing on the sides. Apply shrink wrap using a heat gun to shrink it tight to the tumbler. Bake in a convection oven at approximately 385-400 degrees F for 5-6 minutes, turning halfway. **If your tumbler is touching a metal surface during baking, the shrink wrap will be more likely to melt!Remove from oven and immediately remove shrink wrap and transfer. TUMBLER WILL BE HOT!!No sealant is necessary on sublimation tumblers. *Hand washing is recommended as the high heat in many dishwashers may reactivate the heat and cause it to bleed. For more information on sublimating these, please visit ACC Sublimation Blanks & Designs Facebook group for videos.

Stainless Can Cooler for Sublimation Blank 12oz

Sublimation Metal Beer Bottle Opener- 2 Sided- by INNOSUB USA

Sublimation Standard Can Cooler (Dual Lid) – Kupresso

Bottle Openers - BestSub - Sublimation Blanks,Sublimation Mugs,Heat Press,LaserBox,Engraving Blanks,UV&DTF Printing

Efficient Set for Everyday Use: Our 16 oz 4in1 can cooler beer glasses set includes 25 cups, 25 lids, 25 Screw lids, and 25 reusable straws. With a

ZREGGUR 25packs 16oz 4-in-1 Can Cooler sublimation Blank tumblers with 2 lid and straw, Double Wall Stainless Steel for Insulated Can Holder,Works

Sublimation Metal Beer Bottle Opener- 2 Sided- by INNOSUB USA

Stainless Can Cooler for Sublimation Blank 12oz

White Slap Can Cooler Blanks-Sublimation 3-5-10-20-50-100 packs Neoprene Bulk (1) : Sports & Outdoors

Sublimation Printing Stainless Steel Bottle Opener Blanks | 2 Sided Bottle Opener Blank | Custom Stainless Steel Custom Bottle Opener by INNOSUB USA

PartyPrints 25 Pack Black Blank Can Cooler Sleeves, Customizable Bulk Sublimation Can Coolers, Extra-Thick Collapsible Drink Insulator Sleeve, Beer Can Coolers for Party Beverages: Home & Kitchen