Simpson THA418 4x18 Adjustable Truss Hanger - G90 Galvanized

Product Description

Simpson Strong-Tie THA adjustable truss hangers' extra long straps allow full code nailing and can be field-formed to give top flange hanger convenience. Straps must be bent for top flange hanger installation. PAN nailing helps eliminate splitting of 4x2 truss bottom chords. The Strong-Tie THA418 adjustable truss hange.

Simpson Strong-Tie THA adjustable truss hangers' extra long straps allow full code nailing and can be field-formed to give top flange hanger convenience. Straps must be bent for top flange hanger installation. PAN nailing helps eliminate splitting of 4x2 truss bottom chords. The Strong-Tie THA418 adjustable truss hanger features a G90 Galvanized coating and requires the use of hot-dip galvanized fasteners which meet the specifications of ASTM A153.

• Use all specified fasteners.

• For the THA29, nails used for joist attachment must be driven at an angle so that they penetrate through the corner of the joist and into the header. For all other top flange installations, straighten the double shear nailing tabs and install the nails straight into the joist.

• Top Flange Installation—The straps must be field formed over the header - see table for minimum top flange requirements. Install top and face nails according to the table. Top nails shall not be within 1/4 from the edge of the top flange members.

• Face Mount Installation—Install all face nails according to the table. Not all nail holes will be filled on all models. On models where there are more nail holes than required, the lowest 4 face holes must be filled. Nails used for the joist attachment must be driven at an angle so that they penetrate through the corner of the joist into the header.

• Alternate Installation—The THA 4x hangers may be installed in a top flange configuration using the tabulated fasteners for face mount installation and achieve the face mount installation loads. Install the tabulated face nails into the face and top of the carrying member. Nails used for the joist attachment must be driven at an angle so that they penetrate through the corner of the joist into the header.

• Uplift—Lowest face nails must be filled to achieve uplift loads.

NOTE: The correct fasteners installed in the correct position must be used to achieve published load values

California Residents: WARNING

Simpson Strong Tie HIT418 Top Flange 3-1/2 x 18 I-Joist Hangers

The LSU series attaches double joists or rafters to headers, sloped up or down, and skewed left or right, up to 45°. This product is preferable to similar connectors because of easier installation, higher loads, lower installed cost, or a combination of these features.

Simpson Strong-Tie LSU4.12 - Light Slope/Skew U Hanger by FastoolNow

Simpson Strong-Tie THA418 Adjustable Truss Hanger

Simpson Strong-Tie - Hanger - Truss Hangers - Tropical Construction Supply

The Simpson HTU face mount truss hangers have nail patterns designed specifically for shallow heel heights, so that full allowable loads (with minimum

Simpson HTU28-2 Double 2x8 Heavy Face Mount Truss Hanger - G90 Galvanized

1-8 x 3' A307 Threaded Rod - Hot Dip Galvanized – Fasteners Plus

Simpson Strong-Tie DSC2R-SDS3 - 16 Drag Strut Connector w/SDS Screws - Right Side, Pkg 1The DSC drag-strut connector transfers diaphragm shear forces from a girder truss or beam to shearwalls. The DSC5 has been designed to optimize fastener location.

Simpson Strong-Tie DSC2R-SDS3 Drag Strut Connector - Right

Simpson Strong-Tie - Hanger - Truss Hangers - Tropical Construction Supply

Simpson Strong-Tie Single 4-in x 8-in 14-Gauge G90 Galvanized Face Mount Joist Hanger in the Joist Hangers department at

Steel - Joist Hangers - Building Hardware - The Home Depot

Simpson Strong-Tie THA418 Adjustable Truss Hanger

Steel - Joist Hangers - Building Hardware - The Home Depot

Simpson Strong-Tie S/LBV2.12/8 Light Gauge Hanger 2-1/8 x 8